Anatomy Of A Bathroom Drain Types Of Bathtub Drain Stoppers Round Stoppers With Rings Toe-Touch Stoppers Lift-and-Turn Stoppers Flip-It Stoppers Pop-Up Drain Stoppers Trip-Lever Stoppers Conclusion Bathtub drains are in charge of a lot. They don’t just make it simple to drain the water you use in the tub; they also stop waste from building up in your pipes.

The stopper is one of the largest parts of a bathtub drain. Different drain stopper styles are readily accessible.
The anatomy of the drain itself, however, is usually quite simple.

There could be several alternative setups for the drain in your bathroom. Regardless of the layout, each component is built to perform functions that are similar.

Your tub stopper is designed to prevent water from draining, enabling you to fill the tub.

Your drain will also have a pipe system designed to handle waste and overflow in addition to the stopper. The waste system will stop backing waste from pouring into the clean pipes, and the overflow pipe will take extra water from the drain.

The riser, drain arm, and sanitary tee make up the plumbing system. All of these components are located behind or beneath your tub.

BATHTUB DRAIN STOPPER TYPES The type of stopper your bathtub drain has might tell you a lot about it. You can learn more about the system’s age and the underlying piping mechanisms from this.

The stopper’s main function is almost often to add water to the tub.

Older bathtubs frequently have round stoppers because of their style. These stoppers are put into the drain hole to plug it, as opposed to being incorporated into the inside drain mechanism.

When not in use, you can leave them disconnected on the side or secure them to the tub’s floor with a chain.
Simply raise up on the ring to release the stopper when it’s time to drain the water.

The open drain may allow more hair and dirt to pass through this sort of stopper, which could be a disadvantage. As a result, the likelihood of system blockages accumulating is increased.

Toe-Touch Stoppers


Your foot is used to operate toe-touch stoppers. They’re perfect for those who generally take showers in their bathtub because you don’t have to stoop down to utilize them.

This is especially true for those who suffer from joint and mobility conditions like arthritis.

Use your toe to push the spring-loaded stopper into position. When you’re ready to drain the tub, give the mechanism another gentle push to release the stopper.

Rubber seals that fit around the drain are used in the construction of these stoppers. Water cannot flow down the drain due to the seals’ watertight suction.

If you find that your bathtub appears to be dripping, the seal may have worn out.

Thankfully, you don’t have to rebuild your drainage system entirely in this situation. Simply purchase a brand-new rubber seal in the correct size and replace it.


With a lift-and-turn stopper, you can plug and unhook the drain with one hand. The device is only lifted and twisted into position.
A drain notch and an inner pin will line up once the stopper is actuated. The stopper then plunges down the drain.
The pin latches into the notch as the mechanism is turned farther. This prevents water from seeping in around the stopper by keeping it stable.
You must repeat the turning motion in the other direction to release the stopper. In most configurations, power is spring-loaded.
The water drains as soon as the pin is taken out of the notch and the springs raise the stopper once more.

These stoppers need to be used with drain configurations that were created just for them. The stopper won’t fit in other drains since they lack the proper notch.


Flip-it A drain stopper that is relatively easy to use is a stopper. They are tiny stoppers that can be inserted into drain openings.
Once that is done, you will move a lever on the top from one side to the other.

The rubber seal around the stopper adapts to the borders of the drain when the lever is flipped. Because of the watertight seal, water cannot pass through.

Flip the lever back and take the stopper out of the drain when you’re ready to drain the tub.

It’s vital to remember that the seal may deteriorate over time, much like with toe-touch stoppers. You might need to replace your rubber seal if you start to detect unexplainable leakage.


People use knobs and levers to operate pop-up stoppers, a form of drain stopper. Although these devices are frequently a little more intricate, they may also be simpler to utilize.

Lever, rod, and rocker arm are generally used to construct pop-up stoppers. The arm is connected to the stopper.
The stopper is pushed into or out of the drain when the arm moves.
The arm is joined to the lever via the rod. The stopper will slide into place if you simply pull down on the lever.
Sometimes a knob rather than a lever is available.
Simply pull the lever or turn the knob in the opposite way to remove the stopper and drain the water.

Rods are also utilized by trip-lever stoppers to attach a lever to the stopper. These are frequently utilized with built-in stoppers that occupy a larger portion of the drain.

Hair is kept out of the pipes by a strainer that sits on top of the drain.
The stopper is positioned when you raise the lever. To empty the tub, all you have to do is pull it down.
CONCLUSION Bathtub drains allow the water to drain out of your tub together with the garbage. Additionally, they shield your pipes from waste backflow.
To fill the tub as you take a bath, there are several popular types of drain systems that can be used.





Enter your email address below to

subscribe to my newsletter