1 2 8 Steps to Install a Bathtub on a Concrete Floor Step 1. Secure your spray area Step 2. Level your floor Step 3. Place your bathtub Step 4. Level your bathtub Step 5. Screw the bathtub in Step 6. Insert the drain Step 7. Install the remaining components 1 0 1 1 Are you planning to renovate your bathroom or put in a new bathtub in the downstairs bathroom? A new bathtub can truly make the space come to life.
Depending on the features, it might also give your design a much-needed touch of elegance! However, if you’re working on a cement or concrete floor, you need take extra care.
Without a professional’s assistance, a bathtub can be set up on a concrete floor. However, you should be sure that you are doing it correctly before you start.
When in doubt, seek assistance. You can be sure you won’t harm the bathroom or your bathtub by doing this.
Here is all the information you require regarding installation.
When remodeling their bathrooms, most homeowners choose for an alcove or an acrylic bathtub. While yet being affordable, these tubs are strong enough to survive for many years.
They’re perfect for DIYers because the installation procedure is so straightforward.
You should make sure you have all necessary materials on hand before beginning.
Safe for use on walls waterproof sealing substance Walls can be cleaned with a rag and soap. Using floor coating to level the floor Application of the floor coating with a notch trowel a piece of 2 by 4 wood for supporting the tub using a rubber mallet to tap wood Installation requires wall studs and drywall screws. You will want parts such as: if you intend to install the drain at the same time.
a bathtub threading pipe The tub’s linkage, plunger, and overflow rod a drain pipe (if you dont have a pre-installed copper pipe) To fasten and unfasten the current plumbing, use pliers. The actual installation of a drain is a rather simple procedure. You’ll take measures to make it simple to connect the bathtub drain to the current plumbing.
A BATHTUB CAN BE INSTALLED ON A CONCRETE FLOOR IN 8 STEPS. SECURE YOUR SPRAY AREA IN STEP 1 Any section of the wall or floor that can get wet when you use the tub is referred to as the “spray area.” That refers to the space immediately around the tub.
You need to ensure that this region is waterproof whether you’re working on tile or bare concrete. If not, you might have to deal with mildew.
A waterproof sealant is something you must purchase from a hardware or plumbing store. Use a rag and soap to scrub the walls thoroughly before applying the sealer.
The sealant won’t apply correctly if there is dirt or dust on the surface. It can flake off or be useless.
LEVEL YOUR FLOOR IN STEP 2. If you’re lucky, your floor won’t need any extra attention. However, uneven concrete flooring is quite frequent.
To achieve the proper balance while installing a bathtub, the floor below must be level. A fiberglass bathtub can distort and become damaged by uneven balancing.
Examine your flooring. Are the spaces level? Where?
The concrete slab will then be covered with the waterproof sealer or caulk as the next stage. Using your notched trowel as a guide, apply many layers of this material until you have an even surface.
Before moving on, give the sealant time to thoroughly dry.
3. SET UP YOUR BATHTUB Although it can seem like the simplest step, great attention and patience are actually needed. The bathtub will be placed exactly where it should be.
Place the tub wherever there is a drain pipe in order to make things simpler. Try your best to enclose the tub drain hole with the spout plumbing that already exists.
You might want to collaborate with someone. It’s crucial to be cautious when putting the tub down because being too rough could damage the floor’s surface or the drain itself.
LEVEL YOUR BATHTUB IN STEP 4 You’ll then be concerned with leveling. Make sure the bathtub’s four corners are evenly spaced out on the floor.
Your rubber mallet and 24 will be useful in this situation. To position the wood correctly, you’ll wedge it up against the bathtub and tap it into place. Make sure the tub’s bottom is positioned correctly against the sealant.
STEP 5. INSERT A BATHTUB. The bathtub you purchased ought to have included screws for installation. To attach the bathtub flange to the wall, drill these holes through the drywall.
You can probably find instructions for doing this in the manual. Every six inches of the tub flange should have one screw, on average. Lengthen them if necessary.
Insert the drain in step six. Right now, the bathtub is aligned with the drain pipe that is already there. Once you have reached the bottom of the drain, it is important to take the threading pipe and securely insert it into the male kind of thread.
Since you’re using your current plumbing, this step ought to be rather straightforward.
STEP 7. INSTALL THE LAST FEW PARTS The plumbing will need to be connected to additional bathtub components. The overflow rod, linkage, and plunger are a few of these.
To allow the bathtub to drain extra water, make sure you install them with the overflow hole. Then use screws to tighten the device.
8. THREATEN THE SPOUT This last step is quite easy. Simply grab your spout pipe, place it in the opening, and tighten it using pliers. This step may not be essential for some models because they may already have their spout installed.
CONCLUSION It’s not difficult to install a bathtub on a concrete floor. The floor should be level, and the bathtub model should be positioned correctly. You shouldn’t have any problems as long as you use the right tools and take care of your work.
Plumbing and drain installation ought to be easy. It’s ideal to align the tub with the existing plumbing so that none of the pipes need to be re-threaded.
