You may occasionally experience toilet leakage when flushing. The water leak could be caused by a number of different things.
Depending on the root problem, you might be able to devise a home remedy. You might need to contact a plumber for assistance if you are unable to identify the cause of the leaking toilet.
The first step is to identify the source of the leaky toilet. Where does the water come out?
Is it coming from the base of the toilet, the bottom of the tank, or another location entirely?
LEAKING INTO THE TANK FROM THE BOWL
These are some potential causes if the leak is between the toilet bowl and the tank:
The toilet tank to bowl gasket needs to be replaced. The tank bolts are no longer secure. INSULATION AT THE BASE
A defective wax ring is typically the culprit when the leak starts at the base. A new wax ring that has a more waterproof seal needs to be installed.
A little split in the toilet bowl could also cause a leak. Water won’t remain in the bowl if the crack is large enough.
The items on the bathroom floor will start to give off a foul scent in your bathroom. You might need to completely replace the toilet at this stage.
The majority of leaky toilet repair jobs can be assisted by the following tools:
an updated rubber seal a fresh gasket to join the bowl and tank (including washers and bolts) an allen key with a flathead a flexible wrench a knife for putty a trough the sponge Newspapers for floor protection unclean towels Rubber gloves for hand protection For some fixes, you won’t need all of these tools. However, if any essential ones are missing, you can typically pick them up at your neighborhood hardware store.
A TOILET BASE LEAK’S REPAIR
When you flush the toilet, if water leaks out around the base, the wax ring is virtually probably to blame. You might not detect water on your bathroom floor in this situation.
However, the ceiling on the floor below the toilet will have water damage.
The wax ring forms a seal to stop the leakage of water. You’ll have to relocate the complete toilet in order to replace it. Here is the basic process in steps.
1. STOP GETTING WATER AND EMPTY THE TANK. Cut off the water supply line as you would with any repair. As you work, this will stop more water from leaking out of the pipes.
The toilet’s left side and the back of the tank should both have the pipe’s shut-off valves. Your fingers should be turned clockwise.
The next step is to drain your tank. Using a standard toilet flush is sufficient for this.
Remove the tank lid and press the flush lever firmly to remove as much water as you can.
There will be some water left in the tank. With the sponge, you can soak it up, and then put the sponge in the bucket.
Disconnect the tank’s water supply line. If your fingers are unable to separate it, you can use your adjustable wrench to loosen it.
2. TRANSFER THE TOILET. Make sure the toilet bowl is dry and the tank has been completely drained. Put on your gloves, saturate the sponge with water, and then wring it out into the bucket.
When you relocate the toilet, this will help to avoid a mess.
Your toilet will be securely fastened. Use your wrench to take the bolts out.
If there are caps covering them, first lift the caps with the screwdriver.
After removing the bolts, you can gently shake the toilet to cause the seal to rupture. After that, raise the toilet and place it on the newspapers.
Gases from the sewer could potentially leak through the open drain and into your house. Put an old towel in the drain to block it to stop this from happening.
You must replace the wax ring on the toilet since it cannot be reused. Use your putty knife to scrape out all of the remaining caulk and wax to remove the old ring.
Make sure to inspect the toilet flange while you’re here. Over time, flanges deteriorate and fracture.
If yours needs to be replaced, it will be simplest to do so before the toilet is in place.
3. ASSEMBLING THE NEW WAX RING. The new wax ring is reasonably easy to install. Simply move the wax to the area where the toilet is located.
The edges should be sealed up watertight.
Warming the ring up beforehand is one way to make it glide more readily. This can be accomplished by submerging it in warm water or placing it near a source of sunshine.
The wax will become more flexible as a result.
Some individuals might decide to employ a rubber seal in its place. Rubber seals are frequently recyclable and could last longer.
On top of the flange, a rubber seal needs to be attached. For bolts to hold it in place, there are holes.
4. REINSTALL THE TOILET AND JOIN THE WATER. You will now remove the towel from the drain. Your toilet should be raised and held above the flange.
Line up the bolts with the toilet holes and lower it gradually. If you have someone nearby to assist you, this process is frequently simpler.
After positioning the toilet on the flange, push down while rocking the bowl into position. It will be secured to the wax seal as a result.
The bolts will then be fitted with a nut and washer, tightened with the wrench, and any necessary caps will be put on top of them.
You may attach the supply line to the tank once the toilet is in position. The tank and bowl can then fill by opening the shut-off valve.
Check for leaks after flushing your toilet a few times. In such case, your problem ought to be resolved.
A TOILET TANK LEAK’S REPAIR
Between the toilet tank and the bowl is the other location where leaks are most frequently discovered. When the toilet flushes, this occurs as water moves from the tank into the bowl.
Usually a cracked gasket is at blame. Tanks that wobble can potentially be the result of bad gaskets.
The steps below must be followed in order to remove your tank and replace the gasket:
1. EMPTY AND DRAINS YOUR TANK. You’ll need to shut off your water supply line and completely empty your tank, just like with the fix mentioned above. The solution above provides more thorough instructions for this.
2. GET THE TANK OUT. The tank must be removed from the toilet bowl. It’s not that difficult. Bolting will secure the tank to the basin.
The bolt heads are located inside the tank.
With your tool, remove the washers and nuts from the bolts beneath the tank. Remove the bolts.
The tank can then be raised and placed on top of your newspapers.
The flush valve has the gasket. It is located over the valve nut. Outer gasket is slid.
3. CHANGE OUT THE GASKET. You should slide the new gasket into place after removing the old one. This gasket must completely enclose the valve nut.
Before adding rubber washers, first place a metal washer on the bolts. By doing this, harm to the toilet will be avoided.
After that, replace the bolts that were within the bowl.
Any washers in contact with the toilet should be made of rubber, not metal. This not only avoids damage but also makes a watertight seal to stop tank bolt leakage.
4. Reinstall the tank and reattach the water. The tank will then be raised and reinstalled on the bolts. To seal the tank’s interior, you need add a rubber washer to the bolts.
Then, after adding a metal washer, tighten the nuts.
Double-check the toilet flapper and fill valve. When the tank is first moved, the flapper may need to be adjusted because it has a tendency to move out of position.
You will connect your water supply after the tank is installed, then flush the toilet numerous times. Make sure there are no leaks by checking.
LAST THOUGHTS It’s not always necessary to completely replace a toilet that is leaking. Sometimes you only need to replace the damaged or worn-out parts.
You can frequently fix the seal issue when the toilet leaks around the base. Similar to this, changing the gasket will stop leaks between the tank and bowl.
Over time, these two parts have a tendency to deteriorate.
However, you will have to get a new toilet if the toilet itself has a crack in the bowl. To stop more water from leaking onto the floor, you should immediately turn off the water supply.