1 Top Ways To Remove Drywall Anchors From The Wall Use Pliers To Pull Them Out Remove Them With A Screwdriver Push The Anchor Behind The Wall Cut The Anchor Out 2 How To Patch Drywall Anchor Holes Step 1: Smooth The Hole Step 2: Fill The Hole Step 3: Do A Second Coat 1 Top Ways To Remove Drywall Anchors From The Wall 0 1 Top Ways To Remove Drywall Anchors From The Wall 1 Anchors for drywall come in quite handy. They improve the look and feel of your home by allowing you to hang heavy objects where there aren’t any studs.

They are typically also fairly simple to install. But removing them? That’s an entirely different tale.

There is no one method that works for everyone to remove drywall anchors. Sometimes, getting rid of them is as simple as using pliers to yank them out.

Sometimes you just need to press them into the wall, hammer them out, or screw them in to close the gap.
The best ways to remove drywall anchors are shown below.
Top Methods for Removing Drywall Anchors from the Wall: Pull Them Out With Pliers

Grab a pair of needle-nose pliers and try to gently remove the anchors from the wall before using any harsh measures.
To accomplish this, back and forth wriggle the anchor with your pliers. Try one of the following techniques if the object won’t move.
A SCREWDRIVER IS USED TO REMOVE THEM

Take a flat head screwdriver and place it in the anchor to use this technique. The mouth of your screwdriver should be comparable in size to that of the drywall anchor.

To make sure the screwdriver fits snugly in the anchor, hammer it into place a couple of times.

Now turn your screwdriver in the opposite direction. You’ll need to cut the anchor out or press it into the wall, which we’ll explain below, if it won’t back out of the hole or twists in place.

PUSH THE ANCHOR BACKWARDS

Pushing the anchor deeply enough into the wall to patch it is the simplest option if pulling or screwing don’t work.
To begin, lightly score the area surrounding the anchor using a utility knife. Now insert a flat-head screwdriver into the anchor’s mouth.
After that, smash the edge of the screwdriver until the anchor disappears into the wall.
Joint compound can be used to mend the anchor after it has been retracted.
REMOVE THE ANCHOR

The weight that anchors support is distributed throughout the walls, increasing its security. They can become challenging to remove because of this clinging.

Therefore, you will need to cut off the anchor if you were unable to remove it with pliers or a screwdriver and don’t want to recess it. (Warning: if you don’t take care, this could leave a sizable hole in the wall.)

This is how to eliminate it:

Use a utility knife to lightly score the anchor’s outside perimeter. Use needle-nose pliers to grasp the anchor head and gently wiggle it out of the way. Attempt scoring a slightly greater area if it doesn’t pull out. HOW TO FIX ANCHOR HOLES IN DRYWALL

You must fix the hole after removing the drywall anchor. Fortunately, even if you’re new to home repair jobs, this is simple to complete.
You will require the following to repair the hole:
Pre-made joint compound Useful knife 4-inch putty or drywall knife Sponge for sanding fine grit What you should do is:

First, smooth the hole. With the back of your drywall knife, tap the hole left by the anchor until it is concave. After doing this, you shouldn’t feel any frayed drywall paper.

Use your utility knife to trim off the paper’s jagged edges if the surface seems rough even after tapping.

Fill the hole in step two. Now, place some of your ready-to-use joint compound on the drywall knife’s middle. Place your drywall knife at an angle on the wall just above the hole.

To fill the hole, simply swipe it over it.
Take a perpendicular, opposing motion with your knife. This will make the compound more supple.
Give the compound at least an hour to dry.
(Note: Spackle can be used in place of drywall compound if the hole is extremely small.)
DO A SECOND COAT IN STEP 3. Then, repeat the procedure and fill the hole with a thin layer of drywall compound.
Permit to completely dry.

SAND THE WALL in Step Four. Use a fine-grit sanding sponge to sand the compound until it is smooth and consistent with the rest of the wall after the second coat has dried.

You’re now prepared to begin painting.
CONCLUSION Installing wall anchors is a much easier DIY undertaking than removing them. With needle-nose pliers, remove the anchor as your first line of defense.
Try tightening the anchor or slightly retracting it into the wall if it doesn’t work.
After removing the anchor, you can fill the hole using joint compound to conceal it.