Over the past few years, urinals have grown unexpectedly common in private dwellings. 1 2 6 Steps To Install A Urinal 1. Fit the mounting board. 2. Add the water line. 3. Attach the wall hangers. 4. Install the drain. 5. Install the waste outlet. 6. Hang the urinal up. 3 How Do You Attach A Urinal To The Wall? 1 0 1 1 1 2 1 3 The days when they could only be discovered in public restrooms are long gone.

Even urinals that can be used by both men and women exist.
But there is a good reason for the popularity. The cost of urinals is often low, and they are also simple to install and maintain.
You will need some plumbing knowledge if you want to DIY the procedure, but not as much as with some other bathroom gadgets.

The installation procedure may vary significantly based on the model of urinal because there are numerous distinct types of them. However, these are the standard fundamental steps.

Along with the actual urinal and any related accessories, you’ll also require the following tools:

Does any of those sound intimidating? Clean rags Electric drill Tape measure Tape PVC cement Marker or pencil Level tool Plywood Drywall saw Drill bits If so, working with a plumber might be what you prefer.

But you can begin if all of those things are within your scope.

URINAL 1. INSTALLATION IN SIX STEPS. The mounting board must fit. A crucial part is your mounting board. The urinal will rest on top of this.

In order to give the urinal the support it requires, you should have a mounting board in place. This frequently relieves some of the stress on the wall hangings.

The type of urinal will determine how much weight is supported by the hangings versus the board.

Obtain a piece of plywood with weather protection that is large enough to hold the urinal. Nails should then be used to fix it to the wall studs.

2. FILL IN THE WATER LINE. The waterline should now be added. You must first accurately locate the source of the water line before you can proceed.

Using your marker or pencil, mark the positions of the waterline at a distance of 24 inches from the ground. After that, drill pilot holes along the markers using your power drill.

The hanger screws will be inserted into these holes.

Once you’ve completed that, you should use your drywall saw to cut out the drywall in the proper location. This will enable you to connect the urinal’s water supply and wastewater lines.

The urinal receives water from the water supply line, while waste is removed from the urinal by the wastewater line.

Your pipe should be set up so that it connects to the faucet’s front. However, you must install a shut-off valve for the water supply before you secure the pipe.

In this manner, when performing maintenance, you may easily turn on and off the water.

3. HOLD THE WALL HANGERS IN PLACE. Wall hangers must to be included with your urinal. These will support and hold the porcelain in place while also holding it in place.

The hangers will be placed in the holes you made when you installed your water line.

Nails and screws should also be included in the kit to aid in securing the hangers in the proper location. To ensure that every hanger is at the same level, use your leveling tool one more time.

You won’t have to be concerned about putting the urinal unevenly this way.
It is possible to modify the hangers to meet your needs. The local building codes should be followed by them.

Make sure your hangers are fastened into both the mounting board and the wall. If you want to give your urinal the best possible assistance, this is essential.

4. ASSEMBLING THE DRAIN You haven’t yet fastened the urinal to the wall at this time. Before you do that section, you should install your drain and waste outlet.

Using your model’s manufacturer’s instructions, insert the drain into the urinal.
The urinal’s base should be encircled by a metal ring. Around it, apply a layer of caulk.
After that, insert a strainer into the gap and press it down until a tight seal is achieved.
Then you can move underneath the strainer and attach rubber and metal washers to the drainage system. The system should be secured using a nut.
This will reduce the risk of the drain leaking or coming loose.

5. HOLD THE WASTE OUTLET IN PLACE. The waste pipe need to have been placed at the same time as the water line. Now you can join the waste exit of the urinal to the pipe using PVC cement.

The piping will be sealed by the PVC cement to prevent waste leakage. Make sure the pieces fit together properly because inaccurate measurements could lead to problems later on.

6. HANG UP THE URINE. It’s time to hang the urinal itself now that you’ve completed the installation’s most challenging tasks. It will be raised and held above the hangers by you.

Once it is linked to the waste output point, carefully align it.
With the opening behind it, fasten the urinal to the waste exit. This will make it simple to remove garbage.
Allow the urinal’s weight to rest against the hangers. The hangers’ screws should be tightened until they are securely fastened to the wall.
Once you get a firm grip, just make sure you don’t move any farther. The porcelain substance can crack if you keep tightening the screws.
HOW IS A URINAL ATTACHED TO THE WALL? Wall hangers that can support the weight of the item should be included with the urinal.
The urinal needs to be attached to the hangers, then the provided screws need to be tightened until it is secure.

The screws shouldn’t be too loose, but they also shouldn’t allow the urinal to sag against the wall. The porcelain will crack if you make them too tight.

HOW HIGH SHOULD A URINAL BE MOUNTED?

The typical mounting size for urinals is 24 inches. The distance between the floor and the product’s rim is 24 inches.
Other laws, however, can apply depending on where you live. Local building codes will always take precedence over the usual setup.
Before installing any new plumbing or appliances, you should always make sure you are familiar with your local building codes.

HOW IS URINAL PLUMBING INSTALLED? Prior to hanging the urinal, urinal plumbing installation must be completed. You might be able to DIY the procedure in some circumstances.

In some cases, hiring a qualified plumber to complete the task may make you feel more at ease.

Once more, it’s critical that you educate yourself with your area’s building codes. Depending on the type of urinal you have, your specific plumbing requirements could also change, so you should carefully read any instructions that came with the item.

HOW IS THE URINAL FLANGE INSTALLED? The drainage system includes the flange. It needs to be put inside the drain pipe.
The urinal must then be hung in the proper location above the flange.

Depending on your model, this is still another component that might change. Some models’ weight is borne by the flange itself, while other models rely on the wall hangers.

In conclusion, if you don’t have experience with plumbing, installing a urinal can be challenging. But if you’ve done any basic DIY craftsmanship before, you can definitely handle it.

Just make sure you have instructions and are aware of the building codes in your area.
Along with assembling the urinal’s component parts, you must set up the urinal’s plumbing. Different models will have various benefits and difficulties.
However, you should be able to install urinals in the majority of situations using the techniques mentioned above.